Dish-network 32.0 Uživatelský manuál

Remote ControlUser GuideRemote ControlUser Guide

Table of ContentsQuick SetupVerifying the Key... C-2Inserting the Batteries...

1REMOTE CONTROL OVERVIEWUse this full-function remote control to operate the DISH Network ViP® 922 SlingLoaded™ DVR receiver. Also, you can program

2If you program the remote control to operate other equipment, refer to page C-6 and the following for remote-control operation instructions:• POWER,

3(or TV/VCR), follow the instructions to program the remote to operate the TV using its code, and then repeat those instructions for the DVD/BD playe

45 Scroll the Sort By: (or Aux Device:) list to position the option you wish to select within the blue highlight bar. Then highlight your device’s na

5ENTERING EQUIPMENT CODES10 If the code worked for other buttons, select Yes and continue with step 11. If the code did not work, select No and repe

62 Turn on your ViP922 DVR and access Remote Control settings using a linked remote.Press MENU, select the Settings tile. Then from the Settings scre

78 Press and release the mode button for the device you are setting up (TV, DVD, or AUX).If you are setting up a TV, you can remain in SAT mode and p

C-1Accessing the System WizardRefer to page 12 for informationon System Wizard Press MENU, select Settings and thenSystem Wizard.OR

8SWITCHING BETWEEN TV AND AMPLIFIER VOLUME CONTROLIf a remote control used with the ViP922 DVR has been set up to operate a TV, then MUTE and VOLUME +

9VIEWING EQUIPMENT CODESThese instructions explain how to read out and verify the device code(s) for the equipment you have programmed the remote to

101 Make sure the UHF-2G remote antenna is connected to the correct input on the receiver’s back panel and is not touching anything else. It should be

11COLORED BUTTONSThe following table lists some of these shortcuts for the colored set of buttons on your ViP922 DVR remote control. Note that schedu

12To access the System Wizard from your ViP922 DVR front panel:1 With your receiver turned on, touch the front panel to activate it, and then select M

13TROUBLESHOOTINGWhat’s HappeningWhat’s Wrong What You Can DoThe remote control or one or more buttons on it seems to have stopped working.The remote

14Your receiver is not responding to your linked remote control at all. • The remote control is in the wrong mode.• You might be using the wrong remot

15LIMITED WARRANTYThis warranty extends only to the original user (“you,” “your”) of the DISH Network remote control and is limited to the purchase p

16Advance Exchange ProgramThe Advanced Exchange Program allows you to have a replacement remote shipped immediately to you. Depending upon where you l

17IF YOU NEED HELP1. Review this User Guide.2. See Troubleshooting on page 13.3. Go to the www.dishnetwork.com website and select the link for Suppor

C-2Separate the key from the remote by inserting your thumbnail or a coin in the crease. Remove the key by grasping atthe bottom.Insert the key face u

18REGULATORY FACTORSThis device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:1. this device may not cause

To read out your remote codes, see page 9 for instructions.If your remote is in Limited Mode (see page C-6), then only Volume and Mute buttons work in

For all your customer needs,call the Customer Service Centerat 1-800-333-DISH(3474)176842

C-3Quick SetupConfirm that your remote operates yourreceiver by pressing remote buttons.If this is not working, repeat step 5.If the remote is still n

C-4Quick SetupSelect TV Code and then follow the on-screeninstructions to enter your TV’s device code.Set Up the Remote toControl Your TV1 234To set u

Quick Setup/OperationC-5Placing Your Remotein Limited ModeUse the arrow buttonto highlight Enabled and then select it.23Highlight and select Save.1Sel

Receiver Power & TV PowerTop button turns the receiver on/off,Bottom button turns the TV on/offProgramming required (see C-4)InputPress oncefor In

C-8OperationRemote OperationTV ModeTo use the features described in this section, makesure you are in TV mode by pressing the TV Mode button.Remote pr

C-8OperationRemote OperationDVD ModeDVDTo use the features described in this section, makesure you are in DVD mode by pressing the DVD Mode button.You